DEVICE OVERVIEW
This document contains device specific information for the following devices:
? PIC18F2410 ? PIC18LF2410
? PIC18F2510 ? PIC18LF2510
? PIC18F2515 ? PIC18LF2515
? PIC18F2610 ? PIC18LF2610
? PIC18F4410 ? PIC18LF4410
? PIC18F4510 ? PIC18LF4510
? PIC18F4515 ? PIC18LF4515
? PIC18F4610 ? PIC18LF4610
This family offers the advantages of all PIC18 microcontrollers – namely, high computational performance at an economical price – with the addition of high-endurance, Flash program memory. On top of these features, the PIC18F2X1X/4X1X family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications.
Power-Managed Modes:
? Run: CPU On, Peripherals On
? Idle: CPU Off, Peripherals On
? Sleep: CPU Off, Peripherals Off
? Idle mode Currents Down to 3.0 μA Typical
? Sleep mode Currents Down to 20 nA Typical
? Timer1 Oscillator: 1.8 μA, 32 kHz, 2V
? Watchdog Timer: 2.1 μA
? Two-Speed Oscillator Start-up
Peripheral Highlights:
? High-Current Sink/Source 25 mA/25 mA
? Up to 2 Capture/Compare/PWM (CCP) modules, One with Auto-Shutdown (28-pin devices)
? Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
? Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C? Master and Slave modes
? Enhanced Addressable USART module:
- Supports RS-485, RS-232 and LIN 1.2
- RS-232 operation using internal oscillator block (no external crystal required)
- Auto-wake-up on Start bit
- Auto-Baud Detect
? 10-Bit, Up to 13-Channel Analog-to-Digital Converter module (A/D):
- Auto-acquisition capability
- Conversion available during Sleep
? Dual Analog Comparators with Input Multiplexing
? Programmable 16-Level High/Low-Voltage Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage Detection
Flexible Oscillator Structure:
? Four Crystal modes, Up to 40 MHz
? 4x Phase Lock Loop (PLL) – Available for Crystal and Internal Oscillators
? Two External RC modes, Up to 4 MHz
? Two External Clock modes, Up to 40 MHz
? Internal Oscillator Block:
- 8 user-selectable frequencies, from 31 kHz to 8 MHz
- Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL
- User-tunable to compensate for frequency drift
? Secondary Oscillator using Timer1 @ 32 kHz
? Fail-Safe Clock Monitor:
- Allows for safe shutdown if peripheral clock stops
Special Microcontroller Features:
? C Compiler Optimized Architecture:
- Optional extended instruction set designed to optimize re-entrant code
? 100,000 Erase/Write Cycle Flash Program Memory Typical
? Three Programmable External Interrupts
? Four Input Change Interrupts
? Priority Levels for Interrupts
? 8 x 8 Single-Cycle Hardware Multiplier
? Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
? Single-Supply 5V In-Circuit Serial Programming? (ICSP?) via Two Pins
? In-Circuit Debug (ICD) via Two Pins
? Wide Operating Voltage Range: 2.0V to 5.5V
? Programmable Brown-out Reset (BOR) with Software Enable Option
